Better welding skills for sure.

Won't pass a weld test, So no. Not skillful at all. Read the American Welding Society manual for the reasons. A Certified Welding Inspector would toss this without even bending it for the technique used. This isn't welding, This is sticking two poorly prepped pieces of steel together.

@TheElliot__ i dont think he knows how to weld

@TheElliot__ I’ve never seen a welder compliment another’s job

@TheElliot__ 🤣

The bevel is far too shallow, not getting fusion to both toes, rod angle blows, turn it down/watch heat input or it will deform, and never, ever weave your weld more than 3X the diameter of your welding rod. A wide weave can decrease the strength of your weld by 60% 👎👎

@TheElliot__ Or use a longer bar to begin with? 🤷‍♂️

@TheElliot__ this is a horrible weld and won’t hold up to any sort of pressure at all he needed to add a joint or filler in there for all of that to bind together this person is not a professional, and if they are certified it needs to be revoked, because he’s gonna get someone killed

@TheElliot__ Just weld over the hole after the first pass?

@TheElliot__ Engineering works with experience

@As_saafi10 Damn true

@TheElliot__ No need for that big a chamfer for that thickness of steel bar!

@TheElliot__ He's paid by the electrode.

@TheElliot__ Bad job. The chamfer angle is too large. It looks more than 60°. I think 30° is enough. Huge consumption of time and electrodes. If you spend so much time on a 50 mm seam, you'll go broke.

@TheElliot__ Does this remain the weakest spot on this bar?

@TheElliot__ I's have sent him packing for wasting my time and money. Way too much bevel, too many passes and a waste of rods.

@TheElliot__ That shit will immediately break

@TheElliot__ Another unskilled street shitter doing shit work and calling it quality. Fuckin cunts.

@TheElliot__ Yeah grind that undercut out of there. 😂

@TheElliot__ Bastante habilidad, lo hace ver más fácil de lo que es, aunque es un alarde de habilidad no es la manera más práctica de hacerlo, yo habría colocado una pequeña varilla sobre la unión y la habría fundido habría ahorrado electrodos, que no son baratos, al menos los buenos.

@TheElliot__ Pero deberían comentar que entre cada cordón de soldadura hay que dejar enfriar un tiempo porque de lo contrario se tuercen las piezas a soldar

@TheElliot__ Why are there thousands of videos of non Whites doing shitty work in every trade imaginable?

@TheElliot__ Like a ship builders welding skills

@TheElliot__ Suspended in air...not clamped down. How is this not warping?

@TheElliot__

@TheElliot__

@TheElliot__ Multiple HAV, no pre-heat or PWHT, lovely beads though

@TheElliot__ no

@TheElliot__ Flip it over

@TheElliot__ これはトラックのリーフスプリング？ 折れた板バネのように見えます。 もしそうだとしたら、どれ程熟練の技であっても再利用は無理ですよ。 せいぜい、焼き入れしてタガネとして使う程度。

@TheElliot__ Fail the air bubble is porosity,,

@TheElliot__ Aren’t you suppose to push welds not pull?

@TheElliot__ Now my eyes are fucked. Why didn’t you teach me how to wear a welding hood first?

@TheElliot__ 👍👍👍🙏

@TheElliot__ 90% sure that root pass is shit