He repeats it several more times.
@ArmedJ0y24 B takipçi
9.649.378 görüntüleme
49 Yorum
Yorumlar X (Twitter) üzerindeki orijinal gönderiden alınmıştır

@ArmedJ0y
A trigger guard in a holster could absolutely move a trigger that much, it's well within tolerances and is miles away from how far the trigger would have to be depressed to go off. Meaning the gun could absolutely go off in the holster with pressure or impact of the gun. NOT GREAT SIG.
2.284 beğeni

@ArmedJ0y
👀💧 Barely touching the trigger, not even a MM of actuation on it, and jiggling the slide makes it go off. NOT GREAT.
22.968 beğeni

@ArmedJ0y
Good breakdown for everyone who is confused.
1.535 beğeni

@Im_Jackalope
I’ve heard for ages that the p320 had ND issues, but the sheer amount of testing with relatively consistent problems and results that have come out over the last few months have been insane. Is the QC getting worse or are people looking at the p320 in their safe and testing it
591 beğeni

@ArmedJ0y
Mix of everything if I had to guess. It's not a single cause issue which is partly why it's so squirrelly to nail down why this is happening to some and not others.
245 beğeni

@AlfonsoHegao
@Im_Jackalope Don't forget all the little stealth changes they've made without informing anyone. Means if a gun is kitbashed it will act unpredictably.
4 beğeni

@Im_Jackalope
@ArmedJ0y That’s been one of the major reasons I haven’t gotten one yet

@RTunkku
@AlfonsoHegao @ArmedJ0y I don't see why you, or anyone, would get one ever.
1 beğeni

@Im_Jackalope
@AlfonsoHegao @ArmedJ0y so long as you don’t leave it chambered laying around like a dickhead and don’t carry it you really shouldn’t have an issue. I liked the one I shot and if I found a good deal I’d get one. It would be kept in a 3 inch thick tungsten cube stored in the 4th dimension until range day
1 beğeni

@Im_Jackalope
@AlfonsoHegao @ArmedJ0y And also buying one used to send less money to sig

@stikves
This is their "Boeing 737 MAX" moment. Even someone not at all versed in gun safety can easily see how bad of a mess up this is.
369 beğeni

@mister447
So the screw is to replicate something putting a little rearward travel on the trigger from say the holster or otherwise touching but not pulling the trigger?
329 beğeni

@ArmedJ0y
Yep. Consistent pressure backwards right up to but not reaching the wall
523 beğeni

@ToupeeCostanza
@mister447 sorry, what kind of retarded holster applies pressure to the trigger? how much of a moron do you have to be to use a holster which presses on the trigger
4 beğeni

@legoguy4321
@ArmedJ0y @mister447 Most holsters are somewhat flexible and can scrape the trigger if tolerance isn't absolutely perfect. It's usually not enough force to even be considered a factor to anything but clearly here it's a problem
24 beğeni

@THE_knewsom
@ToupeeCostanza @ArmedJ0y @mister447 It’s been a problem 100 times with 3.5 million p320s in circulation. I’m gonna say that’s probably infrequent enough to not worry about it apart from being a little extra careful when holstering the weapon.
1 beğeni

@legoguy4321
@ToupeeCostanza @ArmedJ0y @mister447 No I think it's a problem enough to warrant being pulled from military service and doing a forced recall. Get the tolerances right this time, and make it so bumping the slide doesn't fire the gun
1 beğeni

@THE_knewsom
@ToupeeCostanza @ArmedJ0y @mister447 But bumping the slide *isn’t* enough to fire the weapon. It’s only enough to fire the weapon if the trigger is depressed nearly to the wall. I bet most polymer frame striker fired pistols would behave similarly.

@mister447
@legoguy4321 @ToupeeCostanza @ArmedJ0y I bet they don't. The guy said it was <1mm of travel. That's nothing. One of the design problems is the 320 has a fully cocked striker. It makes the trigger nicer, but clearly at a cost. Combine that with tolerance stacking and you have a problem.
1 beğeni

@H20orDeath
That's terrifying. It really is Sig Shake Awake
226 beğeni




























