Skip navigation
When Water Pressure Meets Engineering! 💦⚙️
0:00 / 1:00

When Water Pressure Meets Engineering! 💦⚙️

Engineering Knowledge

@DP0STS114K followers

Visit on X
5,380 likesDownloadOriginal post

2,464,488 views

When Water Pressure Meets Engineering! 💦⚙️

31 Comments

Comments from the original post on X (Twitter)

  • Gameskyjumper's profile picture

    @gameskyjumper

    any engineer will tell you to shut off water first.

    20 likes

  • John Drouin's profile picture

    @John_Drew65

    I had to do this last week. This is a temporary patch that usually stays on until the whole pipe is patches. That’s how it is at my place of work.

    13 likes

  • Derek's profile picture

    @MyGoldfishGary

    Flex tape would fix that.

    10 likes

  • co1n3a7r's profile picture

    @co1n3a7r

    😬 All I see is someone wearing gloves... but no eye protection while working on a liquid jet that could strip flesh from bone and trash an eye in a millisecond. If this is your kind of work, be smarter.

    10 likes

  • TREKBEAR -- Pike+ Kirk + Picard's profile picture

    @trekbear1960

    Why not use FLEX-SEAL

    8 likes

  • just the data's profile picture

    @BoisvertTobias

    We used to weld high pressure steam live. They couldn’t shut it off but they could pulse it. It was a trip. In manholes as well. Full leathers. Two minutes in the hole per man. Ahh to be 16 again…

    7 likes

  • Bob Fleming's profile picture

    @BobFlemming19

    That’s not a long term engineered solution It’s the equivalent of a sticking plaster🤷‍♂️

    2 likes

  • Peter JOSEPH Diver's profile picture

    @peterdiver69

    I knew them as Plimco clamps, & when used Subsea on Oil pipe lines, the effect was simular, but if the pipe has degraded to the extent that "fixing a bandage to it" (see above), what can happen is, the transfer of preasure builds on another degraded area, with the same results.🤔

    2 likes

  • Shareshare's profile picture

    @1shareShare1

    patching things up; making repairs and adjustments

    1 like

  • dejay's profile picture

    @dejay81172004

    The pipe needs to be replaced there’s to many clamps. The pipe has some corrosion problems.

    1 like

  • Dopravní Poradce 🇨🇿 /// Слава Україні! 🇺🇦's profile picture

    @DopravniPoradce

    Classic "cípant", as we call it in Czech. It's obviously from german Ziehband, pulling belt...

    1 like

  • Iain's profile picture

    @Iain10117602

    Could you not leave it for the back shift as they have an apprentice that knows where the isolating valve is.

    1 like

  • Senri's profile picture

    @Senritsu_haruhe

    This thing needs belzona

    1 like

  • The Lurking Lurker's profile picture

    @Hentaimaniacs

    Some Belzona would fix this fast

    1 like

  • BoringNobody888's profile picture

    @BoringNobody888

    Meh, now freeze seal the pipe, cut that out and do it right.

    1 like

  • Napoleonic's profile picture

    @Lagrange1020

    Why didn't pressure on the gauge increase after stopping the leak?

    1 like

  • Wargame Red Dragon Enjoyer's profile picture

    @ModemWarsVet

    With NO SAFETY GOOGLES!

    1 like

  • Schitzree's profile picture

    @schitzree

    Adding a 4th patch (that I can see, might be more) to a rusted old pipe instead of replacing the whole thing. Might as well wrap it with duct tape.

  • Petre's profile picture

    @00stone0

    Does anyone see what's happening with the pressure gauge?

  • wootthipong ch's profile picture

    @ionicyuth

    แค่ไม่ใส่แว่น Safety ก็ไม่ผ่านแล้ว ถึงทำได้ก็ไม่รอด