Загрузка видео...

Не удалось загрузить видео

На главную

Is this how you would do it?

20,024 просмотров • 1 месяц назад •via X (Twitter)

Комментарии: 33

Фото профиля Laughing Lions 🦁
Laughing Lions 🦁1 месяц назад

No, this is how I would do it.

Фото профиля Bab Dabbalina
Bab Dabbalina1 месяц назад

However you do it, step 1 is to turn off the water supply

Фото профиля Range 4 Harry
Range 4 Harry1 месяц назад

42¢

Фото профиля BilboBeard
BilboBeard1 месяц назад

Turning the water off would be a good start.

Фото профиля CB Ultimate
CB Ultimate1 месяц назад

1. TURN THE FUCKING WATER OFF. 2. GO BUY A FUCKING SHARK BITE FITTING!

Фото профиля Gary Vincent
Gary Vincent1 месяц назад

First, shut off the water! Then get the proper-size Plex fitting, coupler, or union and install it.

Фото профиля Mad Bomber Hat
Mad Bomber Hat1 месяц назад

Not even close

Фото профиля theUnSub
theUnSub1 месяц назад

No. Turn off the water first, then do something dumb.

Фото профиля Hangtooth
Hangtooth1 месяц назад

Use a damn repair coupling But on a more important note STOP POSTING 3RD WORLD BULLSHIT! I don't want to block you. You post great content but this idiotic crap needs to stop

Фото профиля Damon R Becnel
Damon R Becnel1 месяц назад

One large single coupling, slide down bottom first, then up to top.

Фото профиля Patriots song
Patriots song1 месяц назад

my husband is a plumber. that's not how you do it. a piece of pipe and two couplings.

Фото профиля Conservative Golfer ⛳️🇨🇦
Conservative Golfer ⛳️🇨🇦1 месяц назад

First I would turn the water off...

Фото профиля CobraXXX
CobraXXX1 месяц назад

It would slow down water flow

Фото профиля 🅲🅷🅰🅸🅽🆂 🆁🅴🆀🆄🅸🆁🅴🅳
🅲🅷🅰🅸🅽🆂 🆁🅴🆀🆄🅸🆁🅴🅳1 месяц назад

you should turn the water off first

Фото профиля Rocky Mover
Rocky Mover1 месяц назад

That is from the Democratic School of Plumbing.

Фото профиля RKIK
RKIK1 месяц назад

No

Фото профиля I'm not an alien, I promise.
I'm not an alien, I promise.1 месяц назад

No.

Фото профиля Roger X Patterson
Roger X Patterson1 месяц назад

Every right angle joint causes a pressure head loss in the system. This individual just added four 90 degrees turns where there shouldn't be any.

Фото профиля Zeke
Zeke1 месяц назад

If you have a charge account at the hardware store. The 90 degree L’s are probably $3 a pop. Epoxy and tape first.

Фото профиля Dan Phillips (inspired by a largely true story)
Dan Phillips (inspired by a largely true story)1 месяц назад

TL;DW

Фото профиля FK. it
FK. it1 месяц назад

I really enjoy these shakey finger videos of how to half ass everything. Much appreciated seeing another one. How bout turning off the water first

Фото профиля Captain Obvious 🇺🇸 ⚓️
Captain Obvious 🇺🇸 ⚓️1 месяц назад

I lost brain cells watching this....

Фото профиля S brown
S brown1 месяц назад

Why don’t they turn off the water?

Фото профиля Mr. Irrigation
Mr. Irrigation1 месяц назад

Hmmm....how does that work with 8" hdpe?

Фото профиля fwuff
fwuff1 месяц назад

*watching how much water is being wasted in this video* .. {o - o} ʷʰᵃᵗ ᵃʳᵉ ʸᵒᵘ ᵈᵒⁱⁿᵍ .. s ᴛ ᴏ ʀ ᴘ ᴅ ᴏ ɪ ɴ ɢ ᴛ ʜ ᴏ s ᴇ ᴛ ʜ ɪ ɴ ɢ ᴢ .. {ಠ - ಠ} .. w a s t e f u l .. ✨💖✨

Фото профиля TCNTX
TCNTX1 месяц назад

That's fucking retarted

Фото профиля Charles Paynter
Charles Paynter1 месяц назад

Maybe turn off the water first next time

Фото профиля Richard Goode
Richard Goode1 месяц назад

That's a lesson in stupid

Фото профиля David L.A.
David L.A.1 месяц назад

Just a thought, you could turn off the main and use a couple of slip couplers with a piece of pipe between them. It would look less retarded.

Фото профиля Sammy D’ Bull
Sammy D’ Bull1 месяц назад

Uhhhh ridiculous, one simple slip coupling problem solved!

Фото профиля Veronica Schahczinski
Veronica Schahczinski1 месяц назад

@Kelly4Info LOL turn the water off 1st at the valve or to the house

Фото профиля King Kaliwani
King Kaliwani1 месяц назад

This is easier using self-fusing silicone tape:

Фото профиля Dale Heizer
Dale Heizer1 месяц назад

Wow what a friggin nightmare.

Похожие видео