Ethan Gao's banner
Ethan Gao's profile picture

Ethan Gao

@ga0_lab • 9,399 subscribers

building shit in my dorm room | incoming @neuralink

Shorts

Did you know you can create the Maxwell-Boltzmann distribution with just some balls and a motor? I built this simple device to illustrate it. This is how it works: A spinning agitator pumps energy into ~400 balls, so they bounce around and collide like gas particles in a box. They escape one at a time through a tiny hole, then fall a fixed gap into bins below. Since the hole is so small, every ball leaves with no vertical speed and takes the same time to fall. Constant fall time means how far a ball flies sideways is set purely by its speed. A faster ball goes into a further bin. So each bin is really a speed. Tally all 400 and you get the Maxwell-Boltzmann distribution.

Did you know you can create the Maxwell-Boltzmann distribution with just some balls and a motor? I built this simple device to illustrate it. This is how it works: A spinning agitator pumps energy into ~400 balls, so they bounce around and collide like gas particles in a box. They escape one at a time through a tiny hole, then fall a fixed gap into bins below. Since the hole is so small, every ball leaves with no vertical speed and takes the same time to fall. Constant fall time means how far a ball flies sideways is set purely by its speed. A faster ball goes into a further bin. So each bin is really a speed. Tally all 400 and you get the Maxwell-Boltzmann distribution.

498,547 görüntüleme

We made this omnidirectional "swerve" robot that's about 2.5 inches thick. It's holonomic, meaning it can move in any direction, spin in any direction, simultaneously. There is a quick swap turret with slip ring that gives it even more agility. planning on an especially fun attachment soon, but you can add cameras, lidar, robotic arms, lasers, to name a few. Files are free on my ko-fi. Mechanical BOM is just $110 Even with electronics it's well below $200. For comparison, most robotics competitions use swerve modules (this one has four such modules), and each individual module costs about $500-$1000. Part of the reason i hate competition robotics Swerve is in no way new but what about a thin slab one? Wondering if there are any actual use cases of this thing. Built with James Lin, Thank you Will Yu at The Standard Manufacturing Company for helping support Additionally, thank you LDO motors, SendCutSend, PCBWay.

We made this omnidirectional "swerve" robot that's about 2.5 inches thick. It's holonomic, meaning it can move in any direction, spin in any direction, simultaneously. There is a quick swap turret with slip ring that gives it even more agility. planning on an especially fun attachment soon, but you can add cameras, lidar, robotic arms, lasers, to name a few. Files are free on my ko-fi. Mechanical BOM is just $110 Even with electronics it's well below $200. For comparison, most robotics competitions use swerve modules (this one has four such modules), and each individual module costs about $500-$1000. Part of the reason i hate competition robotics Swerve is in no way new but what about a thin slab one? Wondering if there are any actual use cases of this thing. Built with James Lin, Thank you Will Yu at The Standard Manufacturing Company for helping support Additionally, thank you LDO motors, SendCutSend, PCBWay.

41,962 görüntüleme

Hey anduril

Hey anduril

36,754 görüntüleme

Finally got this portable 3D printer working! It can fold down small enough to fit in a backpack and print things larger than itself in Z. Plenty of issues still, but excited to share how I'm going to solve them for V2.

Finally got this portable 3D printer working! It can fold down small enough to fit in a backpack and print things larger than itself in Z. Plenty of issues still, but excited to share how I'm going to solve them for V2.

18,482 görüntüleme

Can anyone else do this?

Can anyone else do this?

15,735 görüntüleme

The two bottom right gears’ D bore got stripped because the motor gets too hot. What material should I print it in instead?

The two bottom right gears’ D bore got stripped because the motor gets too hot. What material should I print it in instead?

13,719 görüntüleme

Videos

Daha fazla içerik yok.