How to change oil filter
@TheCleanCarClub777 тыс. подписчиков
1 655 170 просмотров
35 комментариев
Комментарии из оригинального поста в X (Twitter)

@Rally__vincent
What a puss. Just pull the damn filter. Also didnt see him lube the gasket on the new one AND HE USED A TOOL TO TIGHTEN IT ON CAUSE FCK THE NEXT GUY. 😆
157 отметок «Нравится»

@brown_adder
@grok should the new filter be lubricated before installing and tightening?
52 отметки «Нравится»

@DuckyOffy
Just NO. You've got to get your hands dirty. Why chance damaging the oil filter housing, which costs a lot to get replaced.
20 отметок «Нравится»

@Stumpsurfer
I've been a Fleet mechanic over 40 years.And you never , ever tighten oil filter in this manner
17 отметок «Нравится»

@Sitofur88
Yeah, no, don't take your car to this guy... That is NOT how to change the filter...
15 отметок «Нравится»

@davidpeck
Unscrew with an exterior rubber clamp to grab like a hand. I will then also remove drain plug and the fill cap for a couple of minutes of drip drain with air flow assistance. Then lube filter gasket, fill filter and lightly tighten by hand and plug the pan.
14 отметок «Нравится»

@sYn0_33
So you’re the prick tightening the absolute hell out of filters using a tool. Screw you sir…Screw you.
10 отметок «Нравится»

@Joelblevins1980
First off, the seal should be lubricated prior to installing. Second, anyone who tightens a filter with a wrench is doing nothing but making their next oil change harder. Hand tight is all that is needed. Anything more risks damage to the threads and a fairly expensive repair.
10 отметок «Нравится»

@KRAD4NJF
Rookie mistake is poking your finger into the center hole of the plastic. You can rip off a piece and now you have a strip of plastic clogging up oil passages.
9 отметок «Нравится»

@speculate_sc
WRONG! Never force your thumb into the plastic directly into the threaded port. Plastic can fall into the filter, causing a clog and your engine to fail.
8 отметок «Нравится»

@txtheater
Been doing my own vehicle maintenance for nearly 60 years and I've never had an oil filter that openly exposed for changing.
8 отметок «Нравится»

@RogerRoger96506
Way over torqued. Lube up the new gasket with a little oil. What is this, amateur hour?
8 отметок «Нравится»

@john_leclair
I have certainly used the screwdriver through the old-fashion oil filter trick before to remove a stuck filter - not to drain the oil.
7 отметок «Нравится»

@Erith2014
Before fitting, the filter must be filled with oil and its gasket lubricated.
6 отметок «Нравится»

@BrianMcgregor_
No lube on the gasket?
4 отметки «Нравится»

@ArturFufkin
Like a 60 yr old guy trying to take a piss at 2am
4 отметки «Нравится»

@donkey_democrat
No, no and no and also JACKASS only HAND TIGHTEN OIL FILTERS.
4 отметки «Нравится»

@genemichael34
Do not use the tool to tighten only tighten by hand and don’t forget to put oil on the gasket
3 отметки «Нравится»

@HawksWing_14
The only thing I didn’t mind is the cup trick. That could work. Over-tightning the filter, not lubricating the new filter’s gasket, not torquing the drain plug to spec were all problematic and probably rage bait.
3 отметки «Нравится»

@JackXplodes
Wrong, they did not lube the seal!
3 отметки «Нравится»













